+高级检索
Al-6.3Cu AC-GTAW电弧增材成形的气孔控制
DOI:
作者:
作者单位:

北京航空航天大学,北京航空航天大学,北京航空航天大学,北京航空航天大学,北京航空航天大学,Cranfield University,UK MKAL

作者简介:

通讯作者:

中图分类号:

基金项目:

北京市科技计划装备制造专项资助项目;中央高校基本科研业务费专项资金资助项目(YWF-15-GJSYS-096)


Porosity Control of Wire + Arc Additively Manufactured Al-6.3Cu Alloy Deposition Using AC-GTAW Process
Author:
Affiliation:

Beihang University,Beihang University,Beihang University,Beihang University,Beihang University,Cranfield University,UK MKAL

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用AC-GTAW工艺进行Al-6.3Cu铝合金电弧填丝单道多层成形试验,针对不同热输入、空气和氩气两种环境及不同送丝速度条件,研究过程参数及环境气氛对成形件内部气孔的影响。结果表明,热输入对气孔的影响最大,控制热输入能减少试件中气孔数量和大小;在适当控制热输入条件下,采用氩气环境和低送丝速度可显著减少内部气孔缺陷。试验发现,I=125A,TS=0.30m/min,氩气环境下,WFS=2.0m/min 时,气孔数量最少,尺寸最小。

    Abstract:

    Al-6.3Cu alloy straight wall samples were produced using AC-GTAW process. The influence of heat input, environmental atmosphere, and wire feed speed on porosity characteristics of deposition samples were investigated. It is observed that heat input is the most important factor affecting the porosity defect. Gas pore counts and its diameter can be reduced with proper heat input. With lower heat input, the gas pores can be further reduced in argon environment and lower wire feed speed. The experimental results show that, in argon environment, with travel speed of 0.30m/min and wire feed speed of 2.0m/min, the gas pores can be controlled effectively.

    参考文献
    相似文献
    引证文献
引用本文

从保强,孙红叶,彭鹏,齐铂金,赵 罡,丁佳洛. Al-6.3Cu AC-GTAW电弧增材成形的气孔控制[J].稀有金属材料与工程,2017,46(5):1359~1364.[Cong Baoqiang, Sun Hongye, Peng Peng, Qi Bojin, Zhao Gang, Ding Jialuo. Porosity Control of Wire + Arc Additively Manufactured Al-6.3Cu Alloy Deposition Using AC-GTAW Process[J]. Rare Metal Materials and Engineering,2017,46(5):1359~1364.]
DOI:[doi]

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2016-01-15
  • 最后修改日期:2016-04-20
  • 录用日期:2016-05-19
  • 在线发布日期: 2017-09-27
  • 出版日期: