燕 翔,陈小雨,刘巨锋,钟 菲,郑根稳,颜永斌,刘 海.热处理对选区激光熔化GH3536合金晶界与拉伸行为的影响[J].稀有金属材料与工程,2021,50(4):1296~1303.[Yan Xiang,Cheng Xiaoyu,Liu Jufeng,Zhong Fei,Wang Shunhua,Zheng Genwen,Liu Hai.Effect of Heat Treatment on Grain Boundary and Tensile Behavior of Selective Laser Melting GH3536 Alloy[J].Rare Metal Materials and Engineering,2021,50(4):1296~1303.]
热处理对选区激光熔化GH3536合金晶界与拉伸行为的影响
投稿时间:2020-04-05  修订日期:2020-07-07
中文关键词:  GH3536  激光选区熔化  显微组织  晶界  力学性能
基金项目:
中文摘要:
      采用选区激光熔化制备了GH3536合金,并分别进行固溶处理和热等静压处理,研究不同热处理手段对GH3536合金的组织形貌、晶界形态及室温拉伸行为的影响。结果表明:沉积态试样的组织由超细柱状亚晶粒与熔池界组成,存在气孔与微裂纹等缺陷;分别经固溶处理和热等静压处理后,二者致密度上升,组织转变为由大小不等的等轴晶粒交替分布组成,但后者沿晶界析出M23C6相,形成锯齿状的弯曲晶界;沉积态试样的拉伸性能表现出各向异性的特点,固溶处理可消除拉伸性能的各向异性,但抗拉强度和屈服强度均有下降,延伸率明显上升。热等静压态试样与固溶态试样相类似,但其抗拉强度、屈服强度和延伸率均有进一步的提高;三种合金的断裂机制均为微孔聚集型的韧性断裂。
Effect of Heat Treatment on Grain Boundary and Tensile Behavior of Selective Laser Melting GH3536 Alloy
英文关键词:GH3536 alloy  Selective laser melting  Microstructure  Grain Boundary  Mechanical Properties
英文摘要:
      The GH3536 alloy was prepared by selective laser melting, and was subjected to solution treatment and hot isostatic pressing, respectively. The effects of different heat treatment methods on the microstructure, grain boundary morphology and room temperature tensile behavior of GH3536 alloy were studied. The results show that the microstructure of the SLM sample consists of ultra-fine columnar sub-grains and pool boundary, with defects such as pores and microcracks. The relative density of the alloy increases after solution treatment and hot isostatic pressing, respectively, and the microstructures of the two alloys consist of alternating equiaxed grains of different sizes. However, the HIP sample precipitated the M23C6 phase along the grain boundary, forming a serrated grain boundary. The tensile properties of the SLM samples show obvious anisotropy. The solution treatment can eliminate the anisotropy of the tensile properties of the sample, but the ultimate tensile strength and yield strength are reduced, and the elongation is significantly increased. The HIP sample is similar to the solid solution sample, but its ultimate tensile strength, yield strength and elongation are further improved. Tensile fracture mechanisms of all three alloys are microporous aggregate-type ductile fracture.
作者单位E-mail
燕 翔 湖北工程学院化学与材料科学学院先进焊接技术湖北省重点实验室 yanxwell@163.com 
陈小雨 湖北工程学院化学与材料科学学院  
刘巨锋 先进焊接技术湖北省重点实验室  
钟 菲 湖北工程学院化学与材料科学学院
先进焊接技术湖北省重点实验室 
zhong4536188@126.com 
郑根稳 湖北工程学院化学与材料科学学院  
颜永斌 湖北工程学院化学与材料科学学院  
刘 海 湖北工程学院化学与材料科学学院  
摘要点击次数: 145
全文下载次数: 50
查看全文  查看/发表评论    HTML
关闭