+高级检索
Ti-6Mo-5V-3Al-2Fe-2Zr合金中次生α相对强度和塑性的影响
作者:
作者单位:

1.沈阳工业大学;2.西北有色金属研究院

作者简介:

通讯作者:

中图分类号:

基金项目:

辽宁省教育厅青年科技人才“育苗”项目(LQGD2020012),陕西省重点研发计划(2020GY-251),国家自然科学基金(51901193)


Effect of secondary α phase on strength and ductility of Ti-6Mo-5V-3Al-2Fe-2Zr alloy
Author:
Affiliation:

Shenyang University of Technology

Fund Project:

辽宁省教育厅青年科技人才“育苗”项目(LQGD2020012),陕西省重点研发计划(2020GY-251),国家自然科学基金(51901193)

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    利用EBSD、扫描电镜和透射电镜观测时效处理后合金的次生α相尺寸、形貌和分布,对时效态合金进行室温拉伸实验,研究次生α相对新型近β钛合金Ti-6Mo-5V-3Al-2Fe-2Zr合金强度和塑性的影响。结果表明:时效温度由520℃升高至560℃,晶内析出的αi相尺寸变化不大但间距明显减小,时效温度继续升高,αi相宽度和间距明显增大。时效时间由4h延长至8h,αi相宽度增大但间距减小,时效时间延长至12h,αi相无明显变化。建立次生α相与合金强度的关系式,并计算次生α相对合金强度的影响项,二者相吻合,表明αi相间距是影响该合金强度的主要因素。经560℃/8h时效处理后,αi相间距最窄,抗拉强度为最高的1502MPa。晶内和晶界析出的次生α相联合影响合金塑性。经560℃/8h时效处理后,形成最小间距的αi相和连续的αGB相,合金塑性最差。经过680℃/8h时效处理后,形成沿晶界分布且向晶内平行生长的αWGB相,此外αGB相不连续且αi相间距最大,合金塑性大幅度提高。

    Abstract:

    The size, morphology and distribution of the secondary α phase were observed by EBSD, SEM and TEM. Tensile properties at room temperature of aged alloys were measured. The effect of secondary α phase on strength and ductility of novel near β titanium alloy, Ti-6Mo-5V-3Al-2Fe-2Zr, has been studied. The results show that with the increase of aging temperature from 520℃ to 560℃, the size of the intragranular αi phase changes little but the spacing decrease. With further increase of aging temperature, the width and spacing of the αi phase increase. As the increase of aging time from 4h to 8h, the width of the αi phase increases but the spacing changes little. When the aging time is 12h, there is no significant change in the αi phase. A relationship equation between secondary α phase and alloy strength has been established, which shows a good agreement with the calculated values of strength change induced by secondary α phase. It can be indicated that the spacing of the αi phase determines the alloy strength. The spacing of αi phase is the smallest and the ultimate tensile strength is the highest 1502MPa after aged at 560℃ for 8h. The alloy ductility is affected by both intragranular α phase and grain boundaries α phase. The continuous αGB phase and αi phase with smallest spacing form after aged at 560℃ for 8h, resulting in poor alloy ductility. The αWGB phase, which is distributed along the grain boundaries and grows parallel into the grains, as well as discontinuous αGB phase and αi phase with largest spacing, form after aged at 680℃ for 8h, resulting in significant improvement of alloy ductility.

    参考文献
    相似文献
    引证文献
引用本文

张浩宇,王川,刘丹,程军,周舸,陈立佳. Ti-6Mo-5V-3Al-2Fe-2Zr合金中次生α相对强度和塑性的影响[J].稀有金属材料与工程,2022,51(6):2137~2143.[Zhang Haoyu, Wang Chuan, Liu Dan, Cheng Jun, Zhou Ge, Chen Lijia. Effect of secondary α phase on strength and ductility of Ti-6Mo-5V-3Al-2Fe-2Zr alloy[J]. Rare Metal Materials and Engineering,2022,51(6):2137~2143.]
DOI:10.12442/j. issn.1002-185X.20210471

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2021-05-27
  • 最后修改日期:2021-06-21
  • 录用日期:2021-07-12
  • 在线发布日期: 2022-07-06
  • 出版日期: 2022-06-29